Konica-minolta KIP 3100 Manual do Utilizador

Version 1.0 KIP 3100 User Guide

Chapter 1 Before Use 1-51. 4 Specifications 1. 4. 1 General Subject Specification Model KIP 3100 Configuration Console Power consumption

Chapter 1 Before Use 1-61. 4. 2 Printer Subject Specification Printing method LED Array Electro photography Photoreceptor Organic Photocondu

Chapter 1 Before Use 1-71. 4. 3 Scanner Subject Specification Scanning method Contact Image Sensor (CIS) (5 pieces of A4 or 8.5” sized CIS) L

Chapter 1 Before Use 1-81. 5 Appearance 1. 5. 1 Front view No. Name Function 1 Main Switch You can turn

Chapter 1 Before Use 1-91. 5. 2 Rear view No. Name Function 1 Exit Cover Open the Exit Cover when you remove

Chapter 1 Before Use 1-101. 6 Specifications for the Scan Original A scan original must satisfy the following specifications. Thickness 0.05

Chapter 1 Before Use 1-11 Not square Wet Metal or fabric material Rough surface (Carbon paper for example) Clipped or stapled KIP KIP KI

Chapter 1 Before Use 1-12The following kinds of originals can be read with using a carrier sheet. Image quality or the reliability of paper feeding

Chapter 1 Before Use 1-131. 7 Specifications for the Printing Paper 1. 7. 1 Improper Printing Paper Do not use the following kinds of pri

Chapter 1 Before Use 1-14 Pre-printed Extremely slippery Extremely sticky Extremely thin and soft OHP Film

(1)Thank you for purchasing the KIP 3100 Multi-Function Printer. This USER'S MANUAL contains functional and operational explanations for the KI

Chapter 1 Before Use 1-151. 7. 3 Treatment against environmental condition Shown below are necessary treatments according to the environmental

Chapter 2 Basic Operation 2-1 Chapter 2 Basic Operation Page 2. 1 Turning on KIP 310

Chapter 2 Basic Operation 2-22. 1 Turning on KIP 3100 1. Ensure the KIP 3100 is plugged into a dedicated wall outlet.

Chapter 2 Basic Operation 2-3 3. The User Interface (UI) starts operating and displays the following Copy Mode Screen in approximately one m

Chapter 2 Basic Operation 2-42. 2 Turning off KIP 3100 1. There is a Power Switch on the right side of KIP 3100. Press the “O” side t

Chapter 2 Basic Operation 2-52. 3 Roll Media Replacement 1. Open Roll Deck (1) and remove the empty roll core.

Chapter 2 Basic Operation 2-63. Raise lever (3) on the Flange (4). Insert each Flange into both ends of the roll media core to be installed.

Chapter 2 Basic Operation 2-74. Push both levers (3) down in either way. Position them flat against the flange to secure the roll media.

Chapter 2 Basic Operation 2-8 6. Insert the leading edge of the roll media under Guide Plate (5) until it touches the feeding r

Chapter 2 Basic Operation 2-97. Hold the green grip (on the middle of Guide Plate) (8) and turn the Guide Plate towards the outside. While hold

(2) Safety Warnings The following warnings are very important in order to safely use this product. These notes are important in preventing danger t

Chapter 2 Basic Operation 2-102. 4 Toner Installation 1. Open the Toner Hatch (1). 2. Slide the green Lever (2) to the righ

Chapter 2 Basic Operation 2-11 3. Pressing down the Cartridge Lock Lever (3), rotate the body (4) of the cartridge to the arrow direction

Chapter 2 Basic Operation 2-12 5. Shake the new Toner Cartridge several times left and right to make the toner smooth. 6. The

Chapter 2 Basic Operation 2-13 7. Rotate the body (4) of the cartridge to the arrow direction (counterclockwise) several rotations to open th

Chapter 2 Basic Operation 2-142. 5 Cut Sheet Media Placement 1. Open the Cut Sheet Feeder table (1). 2. There are several siz

Chapter 2 Basic Operation 2-152. 6 Copying 1. There are several size markings on the Original Table which indicate possible feed positions.

Chapter 2 Basic Operation 2-162. 7 Emergency Stop of a Scan or Copy If necessary, press the Emergency Stop Button (1) on the Scanner Unit to i

Chapter 2 Basic Operation 2-172. 8 Canceling Sleep Mode The KIP 3100 has two Sleep Modes to reduce the power consumption. The KIP 3100 will en

Chapter 2 Basic Operation 2-182. 9 Dehumidifying the Roll Media If the roll paper is extremely humidified, it may cause several kinds of defec

Chapter 3 Error Correction 3-1 Chapter 3 Error Correction page 3. 1 Operator Call Errors 3- 2 3.

(3) WARNING 1. The Power source should be as follows:

Chapter 3 Error Correction 3-23. 1 Operator Call Errors 3. 1. 1 Paper mis-feed errors NOTE (1) Take c

Chapter 3 Error Correction 3-33. 1. 1. 1 Deck Jam / Feeding Jam If either “Deck is jam” or “Feeding Jam” is indicated when the roll paper is mi

Chapter 3 Error Correction 3-4 3. When the feeding rollers catch the paper, turn the middle of the Guide Plate (4) towards the outside.

Chapter 3 Error Correction 3-53. 1. 1. 2 Manual Jam 1. Open the Engine Unit by pulling up both Engine Unit Open Levers (1).

Chapter 3 Error Correction 3-63. 1. 1. 3 Reg. Jam / Internal Jam 1. Open the Engine Unit by pulling up both Engine Unit Open Levers (1).

Chapter 3 Error Correction 3-73. 1. 1. 4 Fuser Jam 1. Open the Engine Unit by pulling up both Engine Unit Open Levers (1).

Chapter 3 Error Correction 3-84. Open the Exit Cover (2). 5. Remove the jammed paper by pulling it to the rear side.

Chapter 3 Error Correction 3-93. 1. 1. 6 Original Jam 1. Open the Scanner Unit by pulling up both Levers (1), and then remove the original.

Chapter 3 Error Correction 3-103. 1. 2 Others 3. 1. 2. 1 Initial state This message is indicated when the KIP 3100 is turned on for the fi

Chapter 3 Error Correction 3-113. 1. 2. 5 Cutter Set NG This message is indicated when the Cutter Knob is not located at the correct position.

(4) CAUTION There are hot items inside of the printer.

Chapter 3 Error Correction 3-123. 2 Call Service Errors In case the following Error Codes for a serious failure appear in the screen; PLEASE

Chapter 4 Maintenance 4-1 Chapter 4 Maintenance page 4. 1 Cleaning 4- 2

Chapter 4 Maintenance 4-24. 1 Cleaning 4. 1. 1 Scanner Unit Clean each Scan Glass, Feeding Rollers and Guide Plates once a week, as the s

Chapter 4 Maintenance 4-3 3. Wipe both the Feed Rollers (4) and the inside surface with a soft dry cloth. 4. Gently press Sca

Chapter 4 Maintenance 4-44. 1. 2 Print Engine Clean each Guide Film and Guide Plate once a week, as the toner or paper dust may accumulate on s

Chapter 4 Maintenance 4-5 3. Close the Engine Unit. NOTE (1) There is a Photoco

Chapter 4 Maintenance 4-64. 1. 3 Touch Screen Clean the Touch Screen once a week. 1. Wipe the Touch Screen with a dry cloth.

Chapter 1 Before Use 1-1 Chapter 1 Before Use page 1. 1 Installation Requirements 1- 2

Chapter 1 Before Use 1-21. 1 Installation Requirements The following conditions are required for installation of the equipment.

Chapter 1 Before Use 1-31. 2 Originals Prohibited from Duplication It is not necessarily allowed to copy every kind of original. You may be pu

Chapter 1 Before Use 1-41. 3 Features (1) KIP 3100 Digital Printer is a single footprint Multi-Function Printer which can copy, scan and prin